Steel density and sheet weight -
kg/m² table for thicknesses 0.5-6 mm
The density of carbon steel used for weight calculations is 7850 kg/m³, or 7.85 kg/dm³, so 1 m² of sheet 1 mm thick weighs 7.85 kg and a 1250x2500 mm sheet of the same thickness about 24.5 kg. This single value underpins weight tables for sections, price lists per tonne and the material balance in the plant. Below we explain where the steel density figure comes from, how it differs from specific weight, how much sheets weigh in thicknesses of 0.5-6 mm and how a zinc coating affects the result.
Data: ArcelorMittal (Orange Book, catalogue E20), Steel Buildings in Europe (referring to EN 1991-1-1, Annex A), HEN-STOL calculations.
Steel density - which value applies in calculations
Steel density is the mass per unit volume of the material. For carbon and low-alloy steels, from which structural, deep-drawing and galvanized sheets are rolled, industrial practice assumes 7850 kg/m³. ArcelorMittal states this value explicitly in its sections catalogue, where masses per linear metre are calculated assuming a steel density of 7850 kg/m³. The weight of sheets and strips is calculated on the same basis.
The same figure appears in several equivalent notations, which is a frequent source of errors in conversions:
Steel density in different units
| Notation | Value | Where it is useful |
|---|---|---|
| kg/m³ | 7850 | mill catalogues, product weight tables |
| kg/dm³ = g/cm³ | 7.85 | workshop formulas, dimensions in dm or cm |
| t/m³ | 7.85 | balance of a batch calculated in tonnes |
| kg/m² per 1 mm of thickness | 7.85 | weight of sheet and cut sheets |
Source: ArcelorMittal, Orange Book; unit conversions: HEN-STOL calculations.
The value of 7850 kg/m³ is a conventional design value. The actual density of a given grade may differ slightly depending on its chemical composition, but steel sheet trading and quotation costing use one common figure.
Density vs specific weight of steel
The two terms are often used interchangeably, although they describe different quantities. Density refers to mass (kg) per unit volume. The specific weight of steel, also called unit weight, refers to the gravitational force acting on a unit volume and is expressed in newtons per cubic metre.
The relationship is simple: unit weight is density multiplied by the acceleration due to gravity. HEN-STOL calculations: 7850 kg/m³ x 9.81 m/s² = 77,009 N/m³, or about 77.0 kN/m³. The Steel Buildings in Europe design guide, prepared by SCI and CTICM, gives a unit weight of 77.0-78.5 kN/m³ for steel and refers to Annex A of EN 1991-1-1 on this point. The upper limit matches the result for an acceleration rounded to 10 m/s² (HEN-STOL calculations: 7850 x 10 = 78,500 N/m³).
In a production plant the distinction matters mainly in documentation: batch weight, part weight and price per tonne are calculated from density, while loads on structures, racks or platforms are calculated from unit weight.
Steel sheet weight - kg/m² table for thicknesses 0.5-6 mm
The weight of 1 m² of steel sheet can be worked out without a calculator. HEN-STOL calculations: weight of 1 m² [kg] = thickness [mm] x 7.85, and sheet weight [kg] = thickness [mm] x width [m] x length [m] x 7.85. The table gives theoretical values for uncoated steel in the thicknesses most often bought by production plants, together with the weight of one sheet in three standard formats.
Theoretical weight of steel sheet at a density of 7850 kg/m³
| Thickness [mm] | Weight of 1 m² [kg] | Sheet 1000x2000 [kg] | Sheet 1250x2500 [kg] | Sheet 1500x3000 [kg] |
|---|---|---|---|---|
| 0.5 | 3.93 | 7.9 | 12.3 | 17.7 |
| 0.6 | 4.71 | 9.4 | 14.7 | 21.2 |
| 0.7 | 5.50 | 11.0 | 17.2 | 24.7 |
| 0.8 | 6.28 | 12.6 | 19.6 | 28.3 |
| 1.0 | 7.85 | 15.7 | 24.5 | 35.3 |
| 1.2 | 9.42 | 18.8 | 29.4 | 42.4 |
| 1.5 | 11.78 | 23.6 | 36.8 | 53.0 |
| 2.0 | 15.70 | 31.4 | 49.1 | 70.7 |
| 2.5 | 19.63 | 39.3 | 61.3 | 88.3 |
| 3.0 | 23.55 | 47.1 | 73.6 | 106.0 |
| 4.0 | 31.40 | 62.8 | 98.1 | 141.3 |
| 5.0 | 39.25 | 78.5 | 122.7 | 176.6 |
| 6.0 | 47.10 | 94.2 | 147.2 | 212.0 |
Source: HEN-STOL calculations, formula: thickness [mm] x 7.85 = kg/m²; sheet weight = kg/m² x sheet area (2.0 m², 3.125 m², 4.5 m²).
For other dimensions, strip lengths and non-standard thicknesses, the steel sheet weight calculator is quicker, and for purchases in coils the steel coil calculator, which converts coil weight into strip length.
Batch weight and number of sheets
The same formula works the other way round when you need to determine how many sheets the ordered tonnage will yield. HEN-STOL calculations for 5 t of 2 mm sheet in the 1250x2500 mm format:
Effect of the zinc coating on the weight of galvanized steel sheet
According to the ArcelorMittal catalogue, the zinc coating designation of hot-dip galvanized sheet to EN 10346 gives the zinc mass in grams per square metre, total for both sides. Z275 means 275 g/m² for both sides together, not for each side separately. According to the ArcelorMittal catalogue, this corresponds to a typical thickness of about 20 µm per side. For comparison, Z100 is about 7 µm per side and Z200 about 14 µm.
The nominal thickness of galvanized sheet includes the coating: the scope of EN 10346 defines thickness as the thickness of the product after coating, and Nippon Steel Slovakia states in its data sheet that the nominal thickness includes the zinc layer. The British SCI explains that the steel core thickness is obtained by subtracting the total coating thickness on both sides from the nominal thickness, taken as 0.04 mm for Z275. Zinc also has a lower density than steel; GalvInfo gives 7140 kg/m³.
HEN-STOL calculations for 1.00 mm Z275 sheet: core 0.96 mm x 7.85 = 7.54 kg/m², plus coating 0.275 kg/m², giving a total of about 7.81 kg/m². The result is approx. 0.5% lower than with the simple formula 1.00 x 7.85 = 7.85 kg/m². With thin sheets the share of the coating increases, but the difference remains small, so the same formula as for black sheet is sufficient for estimating the weight of galvanized sheet. More on this grade and its coating can be found in the article on DX51D Z275 steel sheet.
Why actual weight differs from the table
The table gives the theoretical weight for the nominal thickness. A sheet weighed on the plant scale will show a different value for several reasons:
- the actual thickness lies within the standard tolerance, so a 2 mm sheet may be slightly thinner or thicker; the permissible deviations are described in the article on steel sheet thickness tolerances,
- the width tolerance is positive (Tata Steel specifies a tolerance of 0 to +20 mm for hot-rolled strip with mill edge up to 1850 mm wide), so a strip or sheet may be slightly wider than the nominal dimension,
- the metallic coating and protective oil change the weight by small amounts,
- the density of 7850 kg/m³ is a conventional value, and the chemical composition of the grade affects it only slightly.
When a batch is invoiced by the tonne, the weighed mass is decisive, while the theoretical weight is used for planning material requirements, costing parts and checking that the number of sheets matches the delivery note.
Steel sheets in the HEN-STOL offer
HEN-STOL sells steel sheet without a mill certificate on a wholesale basis, i.e. material supplied without the steel mill's certificate: galvanized steel sheet in thicknesses of 0.30-6.00 mm, cold-rolled steel sheet of 0.30-5.00 mm and hot-rolled steel sheet of 1.20-100 mm. The material is available in coils 100-1800 mm wide weighing 4-24 t, in strips and in sheets.
The offer covers two types of material. Overrolled steel and overproduction are defect-free mill surpluses with properties like those of certified steel, cheaper solely because of the lack of a mill certificate. Second-grade sheet is material with defects that is still suitable for production, and the customer assesses its suitability for their own process. We accept orders from 5 tonnes, with delivery throughout Europe. At the customer's request, a partner service centre cuts coils into sheets or strips; whole coils can also be collected.
See how we can help
In wholesale purchasing, weight translates directly into the number of sheets and the cost per part, so it is worth basing your enquiry on specific dimensions. Please send us the specification: sheet type, grade, thickness, coating, sheet format or strip width and planned tonnage. We will check available batches, advise on the format for cutting and prepare a quotation. The full range of grades, coatings and formats is presented in the HEN-STOL steel sheet offer, with separate pages for galvanized steel sheet, cold-rolled steel sheet and hot-rolled steel sheet.
Frequently asked questions
What is the density of steel?
For calculating the weight of carbon and low-alloy steel products, a density of 7850 kg/m³ is assumed, i.e. 7.85 kg/dm³ or 7.85 g/cm³. Steel mills use this value in their product catalogues, for example ArcelorMittal for section weights. The actual density of a grade may differ slightly, but trade and design rely on a single conventional value.
How does density differ from the specific weight of steel?
Density is mass per unit volume, expressed in kg/m³. Specific weight, also called unit weight, is the gravitational force per unit volume, expressed in kN/m³. For steel, 7850 kg/m³ x 9.81 m/s² gives about 77.0 kN/m³, and the Steel Buildings in Europe guide, citing EN 1991-1-1, gives a range of 77.0-78.5 kN/m³.
How much does 1 m² of steel sheet weigh?
The weight of 1 m² of steel sheet is the thickness in millimetres multiplied by 7.85. A 1 mm sheet weighs 7.85 kg/m², a 2 mm sheet 15.70 kg/m² and a 3 mm sheet 23.55 kg/m². These are theoretical values for the nominal thickness; the actual weight also depends on thickness tolerances and sheet dimensions.
How much does a 1250x2500 mm steel sheet weigh?
A 1250x2500 mm sheet has an area of 3.125 m². At a thickness of 1 mm it weighs about 24.5 kg, at 2 mm about 49.1 kg and at 3 mm about 73.6 kg. The result comes from the formula: thickness in mm x 7.85 x sheet area in m². For other formats, the steel sheet weight calculator is more convenient.
Does the zinc coating change the weight of the sheet?
Only slightly. Z275 means 275 g/m² of zinc in total on both sides, about 20 µm per side. The nominal thickness includes the coating and zinc has a lower density than steel, so a 1 mm Z275 sheet weighs about 7.81 kg/m² instead of 7.85 kg/m². The difference is approx. 0.5%.
Why does a sheet weigh differently on the scale than in the table?
The table gives the theoretical weight for the nominal thickness and dimensions. The actual thickness lies within the standard tolerance, the width tolerance is positive, and the coating and protective oil change the weight slightly. When a batch is invoiced, the weighed mass is decisive, while the table is used for planning and costing.
Sources
- ArcelorMittal, Orange Book - Dimensions of sections, Mass, online edition
- ArcelorMittal Europe, product catalogue E20 - Hot dip galvanised steel, coating table, online edition
- SCI and CTICM (RFCS project SECHALO: ArcelorMittal, Peiner Träger, Corus), Steel Buildings in Europe - Multi-Storey Steel Buildings, Part 3: Actions, 2009
- GalvInfo Center, GalvInfoNote 1.1 Understanding Coating Weight Designations for Zinc-Based Coatings on Steel Sheet, 2020
- SCI, Advisory Desk AD 358 Design thickness of cold formed members and sheeting, New Steel Construction, 2011